This new role enables Centreon to swiftly address potential security issues, keeping users and IT professionals informed while enhancing the overall security posture of its solutions.
The increasing networking of vehicles requires high-performance connectors that ensure safe, fast and interference-free signal transmission. Rosenberger offers a comprehensive portfolio of test equipment for coaxial and differential automotive connector series such as FAKRA, HFM®, RMC®, RosenbergerHSD®, H-MTD® and MTD®. These optimized test adapters allow high-speed data connections to be precisely validated. Standardized test procedures ensure safety and quality.
Standardized high-speed connections ensure reliable implementation over the entire vehicle life cycle. Simulation frameworks with worst-case models help to avoid inconsistent limit values and optimize the evaluation of functional safety. Clear responsibilities and liability assignments along the wire harness supply chain create a reliable basis for OEMs and suppliers.
These solutions support OEMs and suppliers in the safe and efficient development of modern vehicle architectures.
Battery Energy Storage Systems (BESS) are essential for storing renewable energy and ensuring grid stability. However, their implementation comes with inherent risks, particularly related to lithium-ion battery fires.
ESS fires can start from thermal runaway, where one cell failure can trigger a cascade of overheating, leading to fires that are difficult to extinguish and can last for hours or even days. Should a fire breakout, hazardous gases would release from the batteries, posing health risks to nearby communities and causing environmental damage through soil and water contamination. In severe cases, BESS fires have the potential for huge disruptions to locals through property damage and even evacuations.
Traditional detection methods such as flame detectors often fail in the early stages of a BESS fire due to their reliance on visible flames or smoke, which might not be immediately present. Where flame detectors fall short, thermal imaging cameras can significantly improve protection and prevent fires before they ever reach combustion.
 |
| FLIR A700F Advance Smart Sensor |
Comparison with Other Detection Methods.
While flame detectors are designed to detect visible fire, they may miss smoldering or hidden fires—meaning an alert may not be tripped until the fire has escalated to a dangerous level. FLIR thermal imaging cameras can detect heat in low light and see the beginnings of embers as they heat up surrounding materials, even when there's no visible sign of fire. This early detection can prevent escalation or at least minimize damage by providing critical time for action before fires get out of control. Another advantage of thermal cameras is their ability to monitor large areas or multiple battery racks simultaneously, providing comprehensive coverage which is often challenging for point-specific flame detectors.
Conclusion. Incorporating FLIR thermal monitoring into BESS installations not only addresses the critical safety concerns associated with battery fires but also offers a proactive, reliable, and technologically advanced solution. By choosing a FLIR fixed thermal solution, you ensure that your energy storage systems are safeguarded with the industry's leading thermal imaging technology, protecting both your investment and the community from the devastating effects of BESS fires.
The TF-2000 is completely leak-tight in accordance with IP68 ingress protection. Even without an optional probe sleeve, neither condensation nor steam can penetrate the measuring element. This minimises the risk of failures, ensures measurement accuracy, optimises service life and ensures investment security.
The model TF-2000 with a square brass sleeve can be fastened in seconds using quick-mounting brackets, without any copper tubes being soldered on. Instruments, which have several temperature measuring locations, can be equipped in a time-saving and cost-effective manner. Due to its brass design, the square sleeve ensures good heat conduction and prevents contact corrosion. There is no need to apply thermal compound – nor does this compromise on accuracy or response time.
@WIKANews #PAuto
This is why Körber is working with AWS to deliver comprehensive, cloud-based solutions that help customers achieve their goals. Körber is offering its proven PAS-X MES software products as fully managed as-a-service solutions, hosted in the AWS Cloud.
“We are excited to simplify and accelerate the delivery and operation of manufacturing IT solutions for our life sciences customers,” says Lars Hornung, Sr. Principal Alliances & Technology Partners Software at Körber Business Area Pharma. “Together, we empower pharma and biotech organizations developing NextGen therapies to bring them to market faster, more cost-effectively, and more reliably – all without the need for additional infrastructure or IT expertise.”
Körber and AWS are working closely with the industry to establish a qualification strategy for operating PAS-X MES in the AWS Cloud in compliance with regulatory requirements. Other benefits of the AWS Cloud include state-of-the-art cybersecurity, unmatched redundancy and high availability architectures using AWS availability zones.
Leveraging Werum PAS-X MES as a Service, life sciences companies can focus on their core business – manufacturing vital, often life-saving pharmaceutical and biopharmaceutical medicines – while leaving the application and infrastructure support to Körber. Customers' IT responsibility is reduced by 75%. Upfront investment can be decreased by up to 65%, with minimized costs for deployment and operations.”
Körber holds a strong position and reputation in pharma manufacturing, with its Werum PAS-X MES recognized as the market-leading manufacturing execution system. The technology group’s portfolio integrates manufacturing software with pharma-specific transport, inspection, and packaging equipment.
AWS provides solutions and capabilities spanning the entire automation pyramid, which have been successfully implemented across diverse industries. It offers advanced functionality to enhance the MES layer, including data, analytics, and application layers. As a well-established cloud infrastructure and service provider, AWS supports numerous companies in the pharma and life sciences sectors.
AWS provides a robust foundation with AWS landing zone, logging and monitoring, and rapid provisioning capabilities. Customers benefit from enhanced security, as AWS consistently meets thousands of global compliance standards, including ISO 27001 and SOC 2 certifications.
Global leaders in smart building technology, Legrand, Schneider Electric and Siemens Smart Infrastructure have announced the formation of a strategic interest group to tackle critical challenges in providing ultra-resilient and interoperable wireless connectivity everywhere in buildings using the new NR+ technology standard. Supported by wireless industry experts such as last mile semiconductor, Nordic Semiconductor ASA, DSR Corporation and Wirepas, and embedded security expert Kudelski IoT, these companies aim to establish NR+, the new technology standard purpose-built for IoT, as the interoperable connectivity for digital buildings.
“DECT Forum is proud to host the NR+ interest group, which represents a groundbreaking step toward addressing the connectivity challenges in buildings. NR+ is purpose-built for large-scale, dense sensor networks, capable of adapting to various systems while meeting high standards for scalability, cost and reliability. Bringing together global leaders in technology and wireless innovation confirms the potential of NR+ to set a new standard in buildings,” said Andreas Zipp, Chairman of the DECT Forum. This is the worldwide association of companies and organisations in the DECT (Digital Enhanced Cordless Telecommunications) wireless industry. Dedicated to the advancement of DECT and related wireless standards, the DECT Forum promotes innovation, interoperability, and the development of future-proof wireless communication solutions.
Today, 75% of buildings are not energy efficient; they account for 30% of global energy consumption and are responsible for much of the inefficiency within the built environment. The NR+ interest group sees an urgent need for robust connectivity solutions like NR+ that enable cost-efficient, scalable, and reliable digital transformation. The demand for wireless devices in buildings is expected to grow to hundreds of millions annually in the coming years. By implementing NR+ as a global standard, the group seeks to facilitate a transformation toward more sustainable, more energy-efficient buildings capable of adapting to user needs in real-time.
The NR+ interest group will be working closely with silicon vendors, stack vendors, access point providers and smart building standards organizations as well as advocating regulatory adoption to bring the NR+ standard to the forefront of the smart building sector. By aligning technology development with the needs of smart buildings, this initiative will drive a new level of digital transformation for building owners, operators and system integrators.
@DECT_Forum @Wirepas #Wireless #5G #BAS
From restaurants and hotels to assisted living facilities and amusement parks, businesses across the services sector are having trouble finding - and retaining - entry-level workers,according to RobotLAB CEO Elad Inbar. “For better or for worse, our current services sector labor shortage seems here to stay. Fortunately, there is a new way to alleviate this shortage in the form of a new class of tireless workers that emerged during the pandemic: service robots,” He writes in his new book, Our Robotics Future*.
“Robots are not here to take our jobs; they are here to make our jobs more meaningful and revolutionize the way that we work, helping business owners operate more profitably,” Inbar added.
RobotLAB has been at the forefront of the robotics industry since 2007 and is dedicated to making robots smarter and more useful for multiple industries, including restaurants, hotels, assisted living facilities, manufacturing, education, hospitality, healthcare, retail and more.
As the founder and CEO since RobotLAB’s inception, Inbar has led it to nearly $100 million in sales, overseen tens of thousands of successful robotics deployments, and established unique partnerships with manufacturers like LG Electronics and SoftBank Robotics, as well as major hospitality chains such as Hilton, Marriott, Disney and Universal Studios. This uniquely positions him to guide readers through the decision-making process, evaluation, and onboarding of advanced robotics and AI technologies.
In this book, Inbar provides unparalleled insights into the latest technologies and emerging trends that are poised to revolutionize the way businesses operate. He demystifies the current robotics market and shares real-world examples of successful robotics implementations across diverse sectors. Whether readers want to enhance the efficiency of their operations, address labor shortages or stay ahead of the competition, this book provides the knowledge they need to make educated decisions. Inside, readers will discover:
With Our Robotics Future, Inbar combines his extensive expertise with actionable strategies to empower readers to navigate the complexities of robotics adoption with confidence, embrace the future of work, and unlock new opportunities for growth and innovation in their business.
John Bowman, Marketing Director at Anglia, explains, “Many people may not know that Mueller invented the alligator clip, today they are one of the leading manufacturers of cable assemblies and connectors. We’ve now doubled the range of products we offer from this leading manufacturer of high quality, rugged, durable and excellent value electrical clips, test leads, telecom clips, cable assemblies and insulators.”
Mueller Electric are an American manufacturer and are preferred globally by customers in markets including transportation, aviation, instrumentation, underground sensing, grounding, industrial automation, medical, military and construction.
@angliaComponent @muellerelectric @BWW_Comms #Electronics #PAuto
The launch of Megger Industrial Reliability in Britain and Ireland has been announced. This marks a significant milestone in the company’s evolution, driven by the strategic acquisitions of Diagnostic Solutions and Distance. The new division is dedicated to advancing reliability solutions within the industrial sector.
Megger Industrial Reliability is designed to reduce unplanned downtime and extend the lifespan of critical industrial assets. Using techniques such as vibration analysis and advanced monitoring tools, the division provides organisations with actionable data to improve decision-making and streamline maintenance processes.
The approach goes beyond providing technology, focusing on building strong relationships and ensuring success at every step. From commissioning systems on-site to delivering ongoing support, Megger partners with customers to develop tailored reliability plans that address unique challenges and deliver measurable results.
Three tailored packages are available to meet diverse industrial needs. Each package is designed to simplify maintenance workflows while providing expert insights and a clear path to optimising reliability. Whether customers are beginning their reliability journey or seeking to enhance an existing strategy, Megger offers a solution that aligns with their goals.
SK Telecom (SKT), the largest mobile operator in South Korea, and Pohang University of Science and Technology (POSTECH), a university that is a leader in advanced research, have selected the Anritsu Radio Communication Test Station MT8000A for the verification of the technologies used to realize mobile communication that combines antenna expansion technologies with Artificial Intelligence (AI).
Driving this development is a need to address the growing requirement for innovation in 5G-Advanced mobile communication systems, specified in 3GPP Release 18 and beyond. This development has achieved real-time AI-based optimization that helps solve the problem of interference arising from increasing the number of antennas mounted on a smartphone from the typical four to the current maximum of eight. This demonstration utilized the MT8000A as a base station simulator for mobile communications, revealing a remarkable improvement in the data transmission speed despite the smartphone under test remaining the same size as a conventional device and operating within the same frequency bandwidth.
The MT8000A complies with the 3GPP test standards and supports a wide range of tests, including RF measurements, protocol tests, and application tests for 5G mobile network technologies. The hardware is based on a modular architecture, making it easy to reconfigure according to the test requirements, such as higher-order MIMO (4x4 MIMO) and carrier aggregation (8CA).
To contribute to the advancement of cutting-edge telecommunications technology, Anritsu will continue to support R&D for next-generation networks by leveraging 6G and AI while strengthening our efforts to be an innovator in the area of these technologies.
@Anritsu @AnritsuEMEA @postech2020 @SKtelecom @NapierPR #TandM #Communications #Korea
The latest stage of Emerson's next-generation AVENTICS™ Series XV pneumatic valve systems with new flow rates, configurations, accessories, UL certifications and more. These updates give original equipment manufacturers (OEMs) greater design flexibility and scalability to precisely configure valves when engineering handling systems and automation solutions.
In addition to new flow rates and configurations, Series XV valves are also available with UL certifications and more accessories. Both the XV03 and XV05 are designed for compliance with UL429 and UL61010 for quality and safety. New and existing accessories provide greater functionality and include separators, blank stations, pressure supply plates, sandwich pressure supply, and sandwich pressure exhaust. There is also a custom toolbox that contains the most important tools to assemble XV systems.
The next phase of the staged XV release will see the continued launch of new accessories as they become available, as well as greater connectivity. Additional fieldbus protocols will be launched throughout 2025, including Powerlink, CanOpen in mid-2025 and AS-I in late 2025. The valve systems currently support Profinet, Ethernet/IP, EtherCAT, Modbus TCP, Profibus DP and IO-Link.
Next-generation Series XV valves use proven core valve AVENTICS technology and include metal threads, aluminum base plates and compact dimensions to make integration easier. Complete valve systems are easy to commission with the AVENTICS online configurator that streamlines design and layout. To reduce lead times for every global region, three Emerson plants are equipped to manufacture orders.
Providing higher flow rates in a compact valve package, Series XV valves enable more efficient and flexible pneumatic system performance while offering products customized for specific markets, including factory automation, automotive and tire, food and packaging applications. Part of a Floor to CloudTM approach, Series XV valves power machinery and processes at a component level, helping manufacturers boost productivity in applications.
To increase OEM Sales and grow distributor network to reach a larger market.
The appointment of Carola Kristensson as Sales Manager for Central and Northern Europe has been announced by EMIS. Joining the existing team at EMI Solutions AB, the EMIS European office in Stockholm, Carola will be bringing her industrial electronics experience to the company, which is investing heavily in growing their Europe market.
 |
| Carola Kristensson |
EMI Solutions has been designing and manufacturing EMI filters for more than 40 years and is a global source for efficient EMI and EMC solutions across all industries, applications and the frequency spectrum. Products available include EMI/EMC Components, Feedthrough Components, Power Quality, Military Grade Filters and Surge Protection.
The company aims to offer an end-to-end solution to meet industry’s ongoing EMI Challenges. With a robust global supply footprint across eight industry segments, EMIS is continuously investing in technology and skills to deliver its promise of efficiency with seamless customer support. Customers are supported by a very experienced consulting team, a fully equipped Pre-Compliance Lab and a huge safety certified standard product offering of over 2500 part-numbers produced in their own very efficient facility.
@proactivefleet #EMIS #PAuto #Electronics #Europe
Medical power supplies for worldwide use.
The power supplies with protection class I + II and a universal input from 85 to 264 VAC with active PFC are designed for international use in medical technology. The robust and high-quality switching power supplies meet the latest medical safety standards in accordance with IEC/EN/UL 60601-1 Ed. 3.2 (2xMOPP) and the safety approval in accordance with IEC/EN/UL 62368-1 Ed. 3.0. This ensures maximum safety and electromagnetic compatibility for reliable and trouble-free operation in medical environments.
Individual adaptations and design-in support.
In addition to the standard models, Bicker Elektronik also offers customer-specific modifications and has extensive know-how in design-in as well as in the individual dimensioning and adaptation of power supplies. In addition, the power supply specialist also offers customized connection and cable assemblies on request.
Availability and further information.
The power supplies of the CINCON LFM200M and LFM300M series are available now and can be ordered directly from Bicker via personal B2B contact or conveniently 24/7 in the international web shop at www.bicker.de. The Bicker team is happy to provide further information and individual advice.
All product advantages at a glance:
@bicker_de @PresseBox #PSU #Medical
By incorporating Zitara’s advanced battery energy storage systems edge monitoring and control software into its Ovation automation platform, Emerson can now offer customers enhanced energy storage management, optimised battery usage, and improved battery lifetime and safety across various applications.
Emerson’s Ovation software and technologies help utilities meet the increasing demand for reliable, affordable and sustainable power and water. The next-generation platform helps power operators and owners with a complex portfolio of distributed energy resources use real-time data to improve load and demand management. The integration of Zitara’s software will further enhance these capabilities by providing advanced battery monitoring and control solutions that support the growing demand for reliable energy storage solutions.
“We are thrilled to partner and integrate our software into Emerson’s renowned Ovation automation platform,” said Shyam Srinivasan, CEO of Zitara. “This collaboration opens up significant opportunities for both companies, allowing us to provide our customers with state-of-the-art battery management solutions that drive profitability, efficiency and sustainability.”
Emerson and Zitara’s partnership leverages both companies’ strengths to deliver innovative solutions to the market, underscores a shared commitment to advancing technology in the power and water sector, and supports the transition to more sustainable energy solutions. As part of this collaboration, both companies will work closely to ensure seamless integration and deliver exceptional value to their customers.
@EmersonExchange @Emerson_News @EMR_Automation @HHC_Lewis #Zitara #PAuto #Battery
The survey identified charger maintenance as a top concern for the future of the EV industry, with 36% of respondents identifying it as a key challenge. Adding to the complexity, 44% pointed to inoperable chargers as one of the biggest hurdles facing the EV charging infrastructure, closely followed by 40% who cited software incompatibility as a significant obstacle. Compounding these challenges, 88% of respondents highlighted a critical skills gap within the EV workforce, signaling an urgent need for training and development to support the industry's growth.
Summary:
• Over 68% of those surveyed acknowledge the EV industry is falling behind on the adoption curve, highlighting sector-wide challenges. • 40% of respondents predict that widespread charger availability will lag behind demand for up to seven years or longer. • 44% cite inoperable chargers, and 40% highlight software incompatibility as major hurdles to EV charging infrastructure. • 32% of respondents cite predictive maintenance, and 31% highlight artificial intelligence as key to a successful EV charging strategy. |
"I'm encouraged that while 68% of respondents recognize a gap in industry adoption, the survey highlights a strong sense of confidence as industry leaders take proactive steps to address critical challenges," said Alex Chillman, Fluke Vice President of Innovation. "To pave the way for sustained industry growth and innovation, we must prioritize comprehensive worker training and ensure the availability of a reliable, well-maintained charging infrastructure. Charger maintenance also remains a significant concern and addressing it will be essential to meeting the growing demand for electric vehicles."
The survey results underscore Fluke’s call for greater emphasis on proactive maintenance strategies and workforce development to address the skills gap and meet the growing demand for reliable EV charging infrastructure. Respondents identified key factors critical to a successful EV charging strategy, with 32% highlighting predictive maintenance and 31% citing artificial intelligence as essential for optimizing performance.
Additionally, resilient infrastructure design, remote monitoring and diagnostics, and the adoption of standardized best practices were identified as vital for ensuring the reliability, efficiency, and adaptability of the evolving EV charging ecosystem.
"The EV industry is at a defining moment—growth is accelerating, and the demand for reliability has never been higher," said Fluke Chief Product Officer Vineet Thuvara. "Our research reveals a critical need to close maintenance gaps, upskill technicians, and ensure every charging point delivers peak performance. As PDMs (Power Distribution Modules) expand, power quality at every node becomes mission-critical. The path to a sustainable future depends on a smarter, more resilient infrastructure."
@FlukeCorp @NapierPR #TandM Automotive #EV
Group achieves 78 out of 100 points in the EcoVadis sustainability rating.
This combined score puts Endress+Hauser among the top 5 percent of the approximately 150,000 rated companies. The EcoVadis assessment is based on several criteria relating to the environment, labor, human rights and ethics. For Endress+Hauser, the rating is a key metric for gauging its own sustainability performance. It is also a valuable tool for the Group’s customers and suppliers, giving them transparency around whether Endress+Hauser is a reliable partner and meets international standards.
 |
| Dr Peter Selders |
Higher score despite more challenging requirements.
Endress+Hauser has improved its sustainability performance in essentially all areas since last year, increasing its combined score from 71 to 78. EcoVadis rated the Group particularly highly on its performance against environmental and labor standards. “We are very pleased with this result, especially considering that EcoVadis has tightened up its requirements over the same period,” said Julia Schempp, the head of the Endress+Hauser Group’s Corporate Sustainability Office.
All measures disclosed in EcoVadis audits must be supported by detailed evidence of implementation, otherwise they are not taken into account. Here, Endress+Hauser benefits from a structured approach in that it maintains robust, comprehensive documentation of its measures and KPIs. This includes clear guidelines on matters such as work safety and the management of hazardous materials.
Ambitious targets.
The Endress+Hauser Group’s sustainability efforts are also reflected in its emission reduction targets. The Group has committed to reaching net-zero greenhouse gas emissions by 2050 and thus supports the efforts of the Paris Agreement to limit global warming to 1.5°C above pre-industrial levels.
“Sustainability is very important to me personally. We need to protect the climate and the environment to ensure livability for future generations. When they grow up, our children should be able to enjoy the same quality of life as we do now. As a company, we can make an important contribution to shaping change for the better while still being successful financially,” concluded Dr Selders.
@Endress_Hauser @Endress_IN @Endress_UK @Endress_US #PAuto #Sustainable
Contemporary Controls has expanded its line of BACnet routers and gateways to incorporate HTTPS to provide secure Internet communication and protect the integrity of client data. Their resident HTTPS web servers allow for commissioning, status reporting, and troubleshooting using any standard web browser.
The BASrouterSX is a high-performance BACnet router that provides stand-alone routing between BACnet networks such as BACnet/IP, BACnet Ethernet (ISO 8802-3), and BACnet MS/TP. This multi-network router features an MS/TP status webpage with a graphical network map that provides real-time status of all BACnet MS/TP devices on the network. It has advanced features, such as MS/TP slave proxy support with auto-discovery and diagnostic MS/TP frame capture for Wireshark® analysis.
The BASgatewaySX Modbus to BACnet Gateway provides gateway functionality between Modbus Serial (RTU or ASCII), Modbus TCP and BACnet/IP. The gateway supports up to 200 devices and 2000 mapped points and features virtual routing that allows each connected Modbus device to appear as an individual BACnet-compliant device. Using HTTPS webpages and a resident database of common Modbus device profiles, Modbus data points from Modbus Serial or Modbus TCP devices can be mapped to BACnet objects.
@ccontrolsgmbh #Pauto #BMS #Communications
“With this introduction of the Summit M64, Teledyne LeCroy reinforced its industry leadership by providing a powerful platform to develop and troubleshoot the next generation of high performance PCIe devices” said Joe Mendolia, Vice President Marketing, Protocol Solutions Group, Teledyne LeCroy. “We are working closely with the computer industry to provide the analysis features companies need for PCIe storage, HPC and AI technology development. We are confident that engineers transitioning to PCIe 6.x will appreciate the rich library of decodes and analysis capabilities available on all of Teledyne LeCroy’s PCIe test tools.”
@TeledyneLecroy #TandM
With the D-DR 3643 NDT, from DÜRR NDT, the large format flat panel detector of the D-DR series gets an upgrade that is 20% lighter and more robust than ever before. This is made possible by the glass-free TFT sensor, which represents the most important advancement. Due to its active area of 351 x 427 mm, it is perfectly suited for profile images in CUI inspections and for large objects.
Thanks to the integrated shielding, the detector is suitable for X-ray sources up to 450 kV and for gamma sources, with a maximum frame time of 180 seconds. The D-DR 3643 NDT is available with different scintillator options to achieve the best possible contrast and resolution for the intended application.
General advantages of the D-DR series are long battery runtime, hot-swap function and IP 67 protection class. In addition to wireless operation, the detector can also be operated by wired data transmission and power supply.
Like all digital X-ray systems from DÜRR NDT, the D-DR 3643 NDT is also operated with the proven D-Tect X inspection software. Special and easy-to-use functions such as multi-gain calibration always ensure the highest possible image quality. Powerful and intelligent tools, such as the X-filter for fast image optimisation, make image evaluation simple and much more efficient.
@PresseBox #Duer #PAuto #NDT #Manufacturing
@PresseBox #jakobantriebstechnik #PAuto #Manufacturing
The sustainability strategy at Nord Drivesystems for 2025 is focused on acting in an environmentally conscious, responsible and integer manner. A cross-divisional team as well as the management and owners are part of the implementation. Besides their own products, it includes four further fields of action.
The strategy comprises five key aspects:
Products.
When it comes to sustainability, their products are a top priority. This is because the design, life cycle and application areas have an impact on the environment. The concept of sustainability is therefore already rooted in the product development process. “Drives can be found in many areas of industry, where they consume a large proportion of the energy used,” explains Carolin von Rönne. “With efficient drive solutions such as the IE5+ synchronous motor, we want to make a significant contribution to reducing CO₂ emissions.” The Nord ECO service furthermore supports companies in finding the most efficient drive solutions for them.
Governance & processes.
The sustainability management was introduced at Nord in 2022. Since then, the company has achieved important milestones such as an annual sustainability report according to GRI, environmental certifications and the integration of international structures. The central objective in this field of action is the establishment of an international governance structure and CSRD-compliant reporting for the entire Nord Drivesystems Group with 48 subsidiaries in 36 countries because the success of other factors – in particular environment, energy and climate – depends on it.
Environment.
 |
| Nord's IE5+ synchronous motor: high efficiency and compact design |
People.
In times of skills shortage, Nord continues to increase its attractiveness as an employer. The company is currently rolling out a global digital learning management system to offer all employees the opportunity for further individual development. Further targeted campaigns and measures are intended to promote diversity among the workforce. “Inclusion, respect for human rights, strengthening our work culture, safety and continuous transfer of knowledge are only some of the topics we would like to promote”, says Carolin von Rönne.
Supply chain.
Nord wants to reassure its customers and employees that sustainable production is given high priority both at manufacturing facilities and in the upstream supply chain. Risk analyses and other processes are carried out within the framework of the Germany Act on Corporate Due Diligence Obligations in Supply Chains (LKSG).
@NORD_Drive @mepaxIntPR #PAuto #Drives #Sustainability
Inelco Hunter has announced extended availability of Amphenol’s Amphe-PRB series connectors. The new connectors are a versatile solution for one, two, or three-phase applications, accommodating up to five contacts. The connectors also feature a dedicated ground contact. Amphe-PRB series connectors are suitable for a wide range of applications in industries such as alternative energy, telecommunications and anything powered by electric motors, including electric or hybrid vehicles.
Safety is a top priority with the Amphe-PRB connector, as it is designed to be touch-proof. Its rugged construction ensures durability and the ability to withstand exposure to moisture, boasting an impressive IP67 rating. The Amphe-PRB series excels in field installations, offering both crimp and set screw terminations using standard contacts.
One of its most notable characteristics is the quick positive coupling enabled by its reverse bayonet design. This feature allows for a secure connection that reduces installation time, making it easier to ensure a solid, stable connection in high-vibration environments. Additionally, the Amphe-PRB connectors are rated to withstand shocks and vibrations up to 15g, which is critical for applications where consistent connectivity is essential, such as in industrial automation and heavy equipment.
The series has an ingress protection rating of IP67, ensuring that the connectors are fully protected from dust and can withstand immersion in up to one metre of water for 30 minutes. This makes the Amphe-PRB an excellent choice for outdoor and harsh environment applications. The connectors are also UV-resistant and meet the UL F1 standard for UV degradation resistance, which is crucial for components exposed to outdoor conditions.
Specifications include reverse bayonet couplings, an operating voltage of 600V AC Max, a current rating of 46A to 60A, IP2X touch-proof contacts and crimp termination. Certifications include UL94-V0, and the wire size is 8 to 6 AWG (8-16 mm²). Inelco Hunter's in-depth engineering support ensures rapid implementation, speeding up the customer’s time-to-market. Inelco Hunter's engineers will work with the SME engineers. This added-value support is at the core of Inelco Hunter’s philosophy, and has been for over 30 years, setting them apart from the "stock and ship" distributors.
IDEC Corporation is expanding its already extensive photoelectric (PE) sensor portfolio with the new SA1N series of space-saving subminiature PE sensors. The SA1N series provides high accuracy and performance, and it is available in compact barrel and block form factors.
 |
| (not to scale) |
To meet these needs, IDEC has added the SA1N series of subminiature PE sensors to its product lineup. The SA1N sensors are available in two versions:
Both versions are all-in-one devices with built-in amplifiers and sensitivity adjustment control. The barrel-mount version has a 3 to 50mm sensing range, while the block-type can detect over a 5 to 30mm sensing range. Both models are available in NPN or PNP light-on configurations, and both provide a rapid 0.5msec maximum response time.
The sensors each come with flexible 2-meter pigtail wiring, functioning at standard 24VDC with minimal current draw. They operate over a wide -25 to +55DegC temperature range. The barrel-mount version uses a stainless-steel housing and plastic encapsulation to achieve an IP67 rating, while the block-type is rated at IP64.
Effective detection for more applications.
Many types of production line equipment and manufacturing machinery—ranging across industries as varied as medical, food & beverage, and more—require positive presence detection of machine components and positioning/counting of products. The SA1N series of subminiature PE sensors will fit into the limited space available for these types of applications, and it offers a favorable price/performance ratio compared with other more esoteric technology options.
The IDEC SA1N series of subminiature PE sensors are part of a much larger sensing solutions portfolio, providing flexible design options for a wide variety of applications. As with all its products, IDEC offers free tech support for the SA1N, with no service or support contract required.
Offers greater design flexibility and faster time to market.
The Danfoss DM series of programmable displays has been expanded with the launch of the DM-Qt series. The DM-Qt display series supports Qt as a plug-in to PLUS+1® GUIDE, where user interface (UI) design can now be developed through the Qt framework — the new standard for creating embedded display UIs in the automobile industry. Qt offers greater design flexibility and ease of use, enabling displays to be programmed faster and reducing time to market.
In addition to faster, easier UI design, Qt tools enable reuse of templates across multiple device platforms and display brands. Elements of the UI design can be scaled per application requirements. This eliminates the need to create new UI designs from scratch for each different machine platform or display manufacturer.
“Designing graphical user interfaces for our DM displays using Qt tools should take about half as much time as it would with other programs due to its extensive library of preexisting elements and a seamless workflow between design and development,” said Herman Oberoi, Senior Portfolio Manager, Displays, Danfoss Power Solutions. “By supporting the industry standard solution for UI development, we now have a great hardware product with incredible design capabilities powered by Qt.”
DM-Qt displays enable graphical development in Qt Design Studio. Application programming is managed in Danfoss’ PLUS+1 GUIDE software, and the PLUS+1 Service Tool combines Qt-created graphics with application code to program DM-Qt displays. Danfoss will continue to offer its standard DM displays with UI design managed in VBSE, Danfoss’ proprietary graphics development tool within PLUS+1 GUIDE.
DM-Qt displays are available in the same sizes and with the same options as standard DM displays. Sizes include 7-inch, 10-inch, and 12-inch displays, with features such as outstanding sunlight and wide-angle viewability, automatic brightness adjustment, superior touch responsiveness, and rugged design with high ingress protection ratings.
A new generation of TOC monitors for regulatory compliance in pure, ultrapure and WFI water applications has been announced by Swan Analytical. With simple, intuitive controls and rugged components, the new AMI-II LineTOC analysers enhance reliability in the continuous measurement of total organic carbon (TOC).
TOC derived from organics is one of the most common sources of contamination in ultra-pure water systems, so monitoring is mandatory in the pharmaceutical industry, where UPW is used as a process medium, as a solvent, as an ingredient, as medical water for injection, and within APIs, intermediates and reagents. Continuous monitoring and a fast reliable response time are therefore essential – to detect any contamination, to monitor trends and raise alarms of excursions.
The new AMI-II LineTOC provides reagent-free TOC measurement by conductivity differential before and after UV-oxidation. With a new enhanced display/transmitter the analyser offers a wide measurement range from 0 to 1000 ppb with a resolution of 0.01 ppb in its lowest range. A compact version of the AMI-II LineTOC is also available to facilitate greater flexibility where space is of a premium, making it suitable for integration in water purification systems or distribution skids.
Both versions of the AMI-II LineTOC are supplied as a complete working system, which means that it is not necessary to purchase secondary equipment, such as a calibration module for example. Standard equipment includes three sample bottles that can be utilised during functionality and system suitability tests, or as the repository for grab samples – thereby avoiding the need for laboratory analysis.
Looking forward, Russell says: “We are tremendously excited about the opportunities that exist for this new generation of monitors in a variety of sectors where the continuous monitoring of pure and ultrapure water is either essential or mandatory, or both. For example, with IQ/OQ/PQ validation and full compliance to Global Pharmacopoeias and FDA 21 CFR Part 11, the new AMI-II LineTOC will bring peace of mind to pharmaceutical manufacturers and system providers alike.”
TTI IP&E - Europe is now an authorised distributor of Samtec products. TTI will provide a global channel for Samtec’s cables and connectors used in electronic applications with the new partnership. Samtec manufacture broad line of electronic interconnect solutions, including high-speed board-to-board, high-speed cables, mid-board and panel optics, precision RF, flexible stacking, and micro/rugged components and cables.
%20TTI%20HQ.jpg)
“We are very pleased to add Samtec to our supplier line card,” said Lew LaFornara, Senior Vice President, Product and Supplier Marketing. “We look forward to bringing Samtec’s industry-leading connector, cable and fibre optic products to our global customers, many of whom look to TTI and our custom supply chain management programs to minimize supply chain risk, reduce their inventories, and streamline their purchasing processes.”
Rick Skees, Vice President of Distribution, Samtec, declared that “TTI is known throughout the industry as a leader in customer support with a commitment to quality and inventory management. We are very pleased that they will be representing Samtec products in the global distribution channel.”
2822Exp.jpg)
Key features of the Nuvo-2822 include:
Measuring only 164.6mm (W) x 214.6mm (D) x 135.6mm (H), the Nuvo-2822 is perfect for systems with space constraints. It can easily be fitted into a compact control cabinet, mounted within machinery, or tucked away in a tight industrial workspace without affecting accessibility. This small footprint allows it to be integrated into environments where rack computers simply wouldn’t fit.
Aside from its size, this box PC is also made to be durable. The rugged build is designed to handle extreme conditions, with an operating temperature range of -10°C to 60°C or, with the addition of a fan, as high as 70°C. Its Intel® Alder Lake N CPU can process large amounts of data in real time. The Alder Lake N family of CPUs are low-power, cost-effective processors designed primarily for embedded systems, IoT, and edge computing using Intel's 12th-generation Alder Lake architecture. Unlike mainstream Alder Lake chips, the N series focuses solely on efficiency cores (E-cores) rather than performance cores (P-cores).
Its wide-range DC input (12V to 24V) further enhances its ability to adapt to different industrial power setups. This flexibility is particularly valuable in industrial automation, transportation, and remote monitoring applications, where power sources can vary.
Despite its small form factor, the device has dual Gigabit Ethernet ports, four USB 3.0 ports, and two COM ports, offering plenty of options for integrating with existing systems. Support for PCIe and PCI expansion cards makes it flexible enough to handle specialised tasks in industrial control or automation, and storage options are versatile, too, with an M.2 SATA SSD slot and a 2.5” drive bay for added capacity.
The Nuvo-2822 introduces a new feature for improved power efficiency: its “Super Power Saving Mode” dramatically reduces energy consumption when the system is in standby (S4/S5) mode. This makes it practical for anyone aiming to optimise energy and improve the sustainability of their operations, not to mention cost savings, without sacrificing functionality.
Thanks to its compatibility with Neousys’ 100 TOPS Intelligent Frame Grabber Card, powered by the NVIDIA Jetson Orin NX, the system can also be easily upgraded to handle AI inference tasks. This means existing x86-based setups can be transformed into high-performance AI platforms without needing an entirely new infrastructure. By integrating the Intelligent Frame Grabber Card, the Nuvo-2822 can efficiently handle object detection, anomaly detection, and predictive maintenance—all at the edge, reducing latency and reliance on cloud computing.
The Nuvo-2822 offers a high degree of flexibility. It balances performance, efficiency, and adaptability, meaning it can fit naturally into a range of industrial scenarios. Its compact design means it can run easily in tight spaces and contribute to energy-conscious operations, and its practicality makes it an all-arounder for industrial systems with modern challenges.
The Anderson Greenwood Type 84 Pressure Relief Valve (PRV) has been introduced by Emerson. This is specially designed to protect tanks and vessels used in hydrogen and other high-pressure gas applications. With Arlon® 3000XT thermoplastic seating and ASME SA-479 Type S21800 stainless steel spindle material, the Type 84 PRV delivers exceptional leak-tight performance, resistance to embrittlement, optimum seat tightness, high reliability and long service life.
To address these and other issues, Type 84 PRVs are constructed for high-pressure gas applications, with a range of 6,000 pounds per square inch gauge (413 bar gauge) to 20,000 psig (1,379 barg) for H2 and He, and a range of 6,000 psig (413 barg) to 21,756 psig (1,500 barg) for all other gases. It reaches full lift at less than 5% overpressure to protect the vessel or tank to which they are affixed, with zero leakage at 90% of set pressure. The valves feature a unique cartridge assembly design to apply uniform spring pressure, resulting in secure seat sealing and leak-tight performance. They are factory tested with helium and nitrogen, both accepted industry-wide as a substitute for hydrogen.
Anderson Greenwood Type 84 valves comply with key industry standards for safety and performance, including American Society of Mechanical Engineers (ASME) Section VIII and XIII, National Board of Boiler and Pressure Vessel Inspectors (NB) certification, and American Petroleum Institute (API) 527.
